How do you start a Braemar wall heater?

To light the heater: – Turn the gas control knob anti- clockwise from the “0” position to the position. – Depress knob fully and hold down. – Press the igniter button located next to the gas control knob 3-4 times. – Observe the pilot meter to indicate operation of the pilot.

How do I reset my Braemar heater?

– When RESET is flashing, it will be accompanied by a number in the time display, and flashing LED’s on the control panel on the front of the heater. Take note of the number and press the RESET button until RESET disappears.

How do you light a Braemar Ecostar?

Turn the knob to the spark symbol, hold it down for a few seconds and press the igniter button a few times until the metal arrow on the pilot indicator is in the red.

How do you turn off a Braemar heater?

1 Press ON/OFF button. 2 The heater and room fan will start after a short delay (approximately 30-60 seconds) provided set temperature is greater than room temperature. 1 Press ON/OFF button. 2 Heater will turn off, room fan will stop after approximately 60-90 seconds.

How do you remove a gas wall furnace?

How to Remove a Wall Heater

1. Shut down all electricity running to your wall heater (if you’re using an electrical wall heater).
2. Turn off the gas line that is connected to your wall heater (if using a gas unit).
3. Use either a screwdriver or a drill to remove the screws that are holding your wall heater onto the wall.

Why is my heating unit not working?

Dirty and clogged filters are one of the primary causes of furnace problems and can cause high operating costs. The heat exchanger can overheat and shut off quickly when filters are clogged with dust and dirt. This also causes soot buildup on the heat exchanger, which makes your furnace run less efficiently.

Why is my Braemar ducted heating not working?

Troubleshooting common Ducted heating problems / faults: Switch power ON/OFF to reset heater, ensure the circuit breaker has not been tripped. Check the gas supply and pilot light is turned ON. Check the batteries in a Thermostat and Ensure Manual mode is Enabled. Check that minimum of 7 outlets are fully open.

Why did my space heater stop working?

CAUSE: The most common cause for electric heater not working is blown fuses. SOLUTION: To check this, first unplug the device and check the fuse box of the house for blown fuses as well as tripped circuit breakers.

Why won’t my pilot stay lit on my wall heater?

Related Articles. When the pilot on your wall furnace does not stay lit, your furnace won’t heat. A number of reasons can cause the wall furnace to not light, including a damaged thermocouple, a clogged pilot orifice and a disconnected gas supply.

Why is my gas wall heater not lighting?

A pilot that won’t stay lit could be the result of a blockage in the pilot tube. Turn off the gas, clear the tube with compressed air, and relight the pilot. If that doesn’t work, you may need to call a repairman to come and install a new thermocouple.

Do Braemar space heaters have a flue?

Braemar SH18, 25 and WF25 Heaters use a co-axial flue system where air for combustion is drawn from outside through the outer pipe, and combustion products are discharged through the inner pipe to outside. Only genuine Braemar heater flue kits can be used for the installation of this space heater.

How do I install the Braemar eco-superstarspace heater?

Run a bead of “Silicone” around the inner flue and attach both the inner flue and outer flue end-caps. FLUE INSTALLATION IS COMPLETE Refer to the instructions supplied with the Braemar Eco-SuperStarSpace Heater for heater installation.

How many Braemar manuals are there in all-Guides Database?

All-Guides Database contains 25 Braemar Manuals (66 Devices) for Free Downloading (PDF).

How do I mount the heater cover to the wall?

Secure cover bracket (640204) 1610mm from lower edge of heater mount bracket (634791) as shown 2. Connect earth lead from heater cover to body of heater – middle of cover and heater body 3. Locate slots in top of cover over locating tabs on top mounting bracket.